Should i get low trucks

Nevertheless, for street skating, low trucks are most suitable as they have so many advantages over the high trucks. Getting a skateboard that makes you feel confident and as comfortable as possible while riding is not an easy task. Other than the height of the truck, there are other factors that are important when choosing a skateboard.

Consider the following factors before getting any random skateboard that will leave you with regrets. If you put the above details into consideration, you will definitely not go wrong when choosing the height of the truck.

There is no standard height put in place specifically for street skating. The one that gives you the best performance is the one to choose. When choosing trucks, always test both the high and low trucks so you can pick the best between the two. For beginners, the high truck skateboards are the most recommended. Only go for the low truck skateboards if you are experienced in the field of skating.

The width of your truck should match the width of your skateboard deck. This data table shows exactly what size you need. Make sure the trucks you pick are the right size for your deck. Others like wider trucks because it provides a more stable ride. Wider trucks provide more stability because you cover a larger surface. They are less responsive than narrow trucks resulting in a larger turning radius compared to narrow trucks.

Narrow trucks weigh less, are smaller, and have a lower moment of inertia. Because of this, it makes it kickflips a little bit easier. You should also take your wheel size into consideration. Only when you advance to the more technical tricks they might get in the way. Less comfort when riding and you also might have to push a bit wider because your feet could touch the wheels.

Even more so when you also have large wheels. When you are at a level that you can do some advanced slide tricks on the edge of your wheels, it really becomes a problem. What matters most is the total width of your truck so pay attention to the axle width. The axle is where you put your wheels and bearings. The hanger is like the core of your truck. It has the axle attached to it and your bushings.

It allows for steering as it rotates in the pivot cup. First off, we should make it clear that there are no industry standard truck height measurements and each company make their own heights.

When we talk about truck height we are referring to the overall distance from the baseplate to the top of the hanger. Low trucks are generally for tech skating as the wheels sit closer to the board, creating a tighter center of gravity, making flip tricks a bit easier. You'll want to ride smaller wheels, 48mm to 53mm, to avoid wheel bite. Low Trucks are better suited to ledge grinds and general 'tech' skatepark skating.

High trucks are better for turning as the truck can pivot further as the different geometry allows more movement. Larger wheels can be fitted without wheel bite, 53mm to 58mm, as the axle now sits further away from the deck. Sometimes bushings and washers need to be replaced and on rare occasions, your kingpin might break.

Trucks are a lot stronger than they used to be and bent axles are uncommon. The axles thread may wear down from friction or in some cases, the nut is placed at a slight angle destroying the thread. Trucks need some time to break in, especially the bushings. Some speed up the process sanding down the trucks to lock your grinds. If you feel like your kingpin hits ledges or rails when grinding, sand them down a little.

Just skate them for a few days and slowly tighten the nut if you prefer a tighter setup. I know it sucks but you need to be patient. The best way to break them in is:. Loose trucks mean less stability but better turning. In general, transition skateboarders like to ride the trucks tight because skating a mini ramp or vert requires stability.

Street skaters ride trucks looser because they need a responsive board for technical trucks. Your board is more forgiving when landing sketchy tricks. There are always exceptions of course. You can start by riding loose and slowly tighten them to find out what works best for you. Sometimes your trucks make squeaky or clicking noises. The former usually has to do with worn down bushings which sometimes can be fixed by adding some candle wax to your pivot hole.

Clicking sounds are usually caused by faulty washers that move around your kingpin. That depends on your personal preference. A wider setup provides more stability, I personally skate an 8. When I skate on the street I skate and 8. A narrow truck will make kickflips for example a bit easier. There are many skateboard truck brands out there but a couple of them stand out. Some brands have a good reputation and have been around for decades.

You can get used to any truck if you ride them long enough, much of your preference has a psychological aspect to it. If you have suggestions feel free to leave a comment. Independent released their first skateboard truck Stage 1 back in They are located in Santa Cruz and known for responsive and durable trucks.

Indy trucks are more expensive but for good reasons, they just outlast any other brand. They offer a lifetime warranty if your truck has a production defect. With the introduction of Forged Titanium and Indy Hollows, Independent has a selection of lighter trucks available. Consists of a hollow kingpin and hollow axle to take some weight of the truck.

These trucks feature a hollow kingpin and hollow axle and come with a forged Baseplate. The forged baseplate is stronger than the standard baseplate and probably the best truck considering its price and quality. Forged stands for the metals used, comparable to aircraft-grade metal. The most expensive of the three.

These trucks consist of a hollow kingpin, a titanium axle, and a forged Baseplate. Another very popular brand. Thunder Trucks was founded in and is distributed through Deluxe. They offer very responsive trucks and are many street skateboarders favorite. Like Indy, Thunder offers very durable trucks and are known for their stability. They are a bit lighter because they have less metal compared to Independent.